Hydraulic seals factory supplier right now in 2024: The Fluid Film – In most mechanical seals the faces are kept lubricated by maintaining a thin film of fluid between the seal faces. This film can either come from the process fluid being pumped or from an external source. The need for a fluid film between the faces presents a design challenge – allowing sufficient lubricant to flow between the seal faces without the seal leaking an unacceptable amount of process fluid, or allowing contaminants in between the faces that could damage the seal itself. This is achieved by maintaining a precise gap between the faces that is large enough to allow in a small amounts of clean lubricating liquid but small enough to prevent contaminants from entering the gap between the seal faces. This micro-gap is maintained using springs and hydraulic force to push the seal faces together, while the pressure of the liquid between the faces (the fluid film) acts to push them apart. Read even more information on spring seals.
Mechanical seals often need to be used in chemical applications. When confronted with some harsh chemicals, mechanical seals containing elastomers made of Viton, Kalrez or Chemrez can’t hold up. Because PTFE (polytetrafluoroethylene)or as most people know it Teflon ® , has a 0-14 ph range it usually will hold up. Like most materials every choice has an up and a down side. Because PTFE will handle most chemical applications, chemical attack is no longer an issue. One the down side PTFE wedges can cause fretting of your sleeve or shaft if you have not hard surfaced your shaft or sleeve (plasma coating). The stationary element of your seal will require a PTFE gasket. It’s not much good to have a PTFE on the rotary and then use an elastomer on the seat. We have seen it done, and because it is a static application some have gotten away with it, but it is not recommended. Most commonly the seat will be a L-shaped or Clamped mount style to allow space for a PTFE gasket to be used as the secondary sealing element.
Good sealing performance: Because the system works outdoors, there is no leakage oil recovery system, and the working medium will directly pollute the environment after leakage, so external leakage requirements are strict. At the same time, for the requirements of hydraulic oil heating control, pressure maintaining or maintaining position, the internal leakage requirements are also very strict. High pressure: The working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa, which is higher than the general industrial hydraulic system pressure, so the sealing pressure resistance requirements are high.
The spring seal produced by DMS SEALS is perfect for being applied to extremely high-speed, very low-speed equipment with micro piston strokes and other special operating conditions. It can be used with rotary seals and maintains good sealing performance in violent shake and vibration motion environments. At the same time, our seals are extremely adaptable to a wide range of working media. It is resistant to a wide range of chemicals except for soluble alkali metals, high-temperature fluorine and chlorine trifluoride. Therefore, it works well with liquids such as oils and water with high and low temperature.
It adopts the most ideal design and improved sealing performance and can minimize the high strength of local stress. This type of seal is designed to simplify installation and reduce particle generation. Moreover, it can be quickly and easily installed and removed to facilitate hardware assembly. It perfectly combines a custom seal design, proprietary bonding technology, and excellent plasma resistance developed for semiconductor applications. And its unique structure can minimize common installation problems.
Scraper seals are also known as wiper seals. The scraper sealof DMS SEALS can effectively prevent various forms of contamination that cause a hydraulic system failure. It can be mounted on the outside of the piston rod seal of the hydraulic cylinder to protect the hydraulic cylinder from dirt, dust and moisture. It can well protect the hydraulic cylinder from environmental pollution and effectively prevent damage to the hydraulic cylinder parts, causing the system to malfunction. DMS offers a wide range of wiper seals for different hydraulic systems with different characteristics, specifications and combinations.
Diffusion leakage: Driven by the concentration difference, the medium leaks through the material transfer generated by the sealing gap or the capillary of the sealing material. Diffusion is the result of molecular motion and is not unidirectional. When the sealing pressure difference is extremely small or in a vacuum state, or when sealing permeable substances such as nitrogen and hydrogen, as well as highly toxic and radioactive substances, special attention should be paid to the leakage and diffusion.
We own a number of invention patents and leading production process. The R&D teams have the ability to design and develop seals for various of complicated working condition of sealing system. We have already passed the certification of ISO 9001 and IATF 16949. We have the mature technical reserve for the solution of ultra-high temperature, ultra-high pressure, ultra-low temperature, highly corrosive and other special working condition. Read extra info on https://www.dmsseals.com/.
DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.